How Landscape Architects Coordinate Community Amenities With Your Site Plan

A landscape architect coordinates community amenities with your civil engineer and architect across four site conditions. Each one adds cost when you resolve it late.

Grading and Drainage

Amenity pads need flat, drainable surfaces. Pool decks slope away from the water, plazas shed to inlets, and lawns need positive drainage to avoid standing water. We set deck and finished grade elevations with your civil engineer so the amenity area ties into site grading without extra retaining walls. Accessible routes carry a 5 percent maximum running slope (1:20) and a 1:48 maximum cross slope under the 2010 ADA Standards.

Utilities and Service Connections

Splash pads need potable water and drainage. Pool equipment areas need electric service, water, and sewer or backwash disposal. Lighting, irrigation, and restroom buildings add more connections. We locate the amenity area near planned service lines and mark stub locations on our plans, so your engineer sizes mains and conduit for the full program.

Accessible Routes and Code Compliance

Every amenity needs an accessible route from parking and sidewalks. We design routes, play surfaces, pool access, and site furnishings to the 2010 ADA Standards for Accessible Design. Local building and health department codes add requirements for pools, splash pads, and shade structures, and we design to them from schematic design.

Phasing and Budget Alignment

Master-planned communities often open the amenity center with an early phase to support sales. We size the first phase for the full program, reserve space and utility stubs for later additions, and give your team quantities for budget alignment.

Community amenities design plan by Evergreen Design Group for a residential development

Residential Amenity Space Design

Residential amenity space design with pool deck and shaded gathering area for a multifamily communityPool Areas and Pool Decks

We design the pool deck, surrounding site, and equipment area for residential pool complexes and produce the construction documents for them. Deck layout follows state and county health department rules for barriers, gates, and clear zones. Pool entries and lifts follow the 2010 ADA Standards, as the Access Board guide to swimming pools, wading pools, and spas explains. We coordinate the pool shell, mechanical systems, and building connections with your pool engineer and architect, and deck drainage with your civil engineer. Shade structures and lounge zones sit where staff and residents keep clear sight lines to the water.

Playgrounds and Tot Lots

Playgrounds follow the CPSC Public Playground Safety Handbook, ASTM F1487 for equipment, and ASTM F1292 for impact-attenuating surfacing. We set use zones, fall heights, and surfacing depth on the plans and provide an accessible route to and into the play area under the 2010 ADA Standards. Equipment layout and surfacing get coordinated with your contractor and equipment supplier before bid.

Dog Parks

Dog parks need a double-gated entry, separate areas for small and large dogs where space allows, and a surface that drains after rain. We select fencing height, surfacing, and drainage for the expected dog count, and we place the park away from pool decks and playgrounds with a planted buffer. Water service for a fountain and hose bib is marked for your civil engineer.

Pavilions, Cabanas, and Shade Structures

Shade structures anchor the amenity area. We size them to the seating count, orient them against afternoon sun and prevailing wind, and detail footings and slab edges for your structural engineer to confirm. Pavilion pads, outdoor kitchen counters, and grill stations get gas, electric, and water stubs on the plans.

Gathering Lawns and Multi-Use Open Space

We shape lawn panels with slopes gentle enough for events and informal play, and place them beside pavilions, trails, and pools so one program feeds the next. Our irrigation design follows the turf layout, so heads cover the lawn without spraying walks and seating.

Walking Trails and Fitness Loops

Trail loops connect amenity areas to housing and to each other. We set path width, surface, and grade to accessible route criteria where terrain allows, and place fitness stations along the loop with open sight lines and lighting coverage.

Outdoor Kitchens, Fire Pits, and Lounges

Grill stations, fire pits, and lounge seating extend use through the cooler months. We specify masonry, concrete, and stainless steel for high-use finishes, and show fuel and electric service and clearances from structures and plantings on the plans.

Commercial and Mixed-Use Site Amenities Design

Commercial site amenities design serves office parks, mixed-use developments, retail centers, and Class A multifamily properties, where outdoor community amenities support leasing and tenant retention.

Commercial site amenities design with courtyard seating and plaza for a mixed-use developmentCommunal Courtyards and Plazas

Our hardscape design for courtyards and plazas covers paving, seat walls, planting, and lighting coordination around building entries, retail frontage, and fire access. Surfaces shed water to inlets your civil engineer places, and paving patterns mark the routes tenants and visitors use.

Outdoor Workspaces

Shaded seating with power and Wi-Fi coverage gives tenants a place to work outside. We place outdoor workspaces on the shaded side of the building, coordinate electrical conduit with your engineer, and select paving and furnishings for daily use.

Rooftop Amenity Decks and Green Roofs

Rooftop decks add usable area, and green roofs reduce storm-water runoff and heat gain. We coordinate structural loads, waterproofing, drainage, and planting depth with your architect and structural engineer, and select lightweight growing media and pavers to match the deck load limit.

Outdoor Fitness Areas

Ground-level fitness zones and wellness gardens suit properties with limited indoor gym space. We size surfacing, equipment spacing, and shade for the expected users, and connect the zone to the property walking routes.

Public and Municipal Community Amenities Design

EDG designs public community amenities for municipalities, public agencies, and civic institutions. Public work follows ADA requirements, universal design, and the plan review and procurement rules of the owner.

City Parks and Pocket Parks

Parks combine active and passive uses for all ages and abilities. We use permeable pavers and native planting to manage rainwater at the source, and design routes that connect to transit stops, bike lanes, and sidewalks.

Community Gardens

Community garden plots need raised beds, water service, tool storage, and accessible paths. We size plots and aisles for wheelchair reach and place hose bibs or irrigation near every bed.

Picnic Areas and Shade Shelters

Picnic areas pair shelters with tables, grills, and accessible paths. We size shelters to the expected group size and place them near parking and restrooms.

Athletic Courts

Basketball, tennis, and pickleball courts need consistent slopes, fencing, and lighting layouts. We coordinate court orientation, surfacing, fence height, and light pole locations with your electrical engineer, and set drainage to keep water off the playing surface.

Splash Pads and Water Features

State and local health departments regulate splash pads. The first design decision is whether the pad recirculates and treats water or runs flow-through, since the choice sets the equipment room, drainage, and utility demand. We design the surface, spray layout, drainage, and equipment access, and coordinate treatment and mechanical systems with the specialty engineer.

Trails and Corridor Conversions

Old rail and road corridors convert to linear parks and trails, which restores habitat and gives the community recreation access. We design surfacing, grades, crossings, and planting for these corridors.

What You Receive on a Community Amenities Project

 

EDG delivers construction documents for your community amenities, not conceptual renderings. A community amenities package includes:

  • Amenity program and site layout coordinated with your civil site plan
  • Grading and drainage coordination for each amenity area
  • Hardscape layout, materials, and construction details
  • Coordinated planting plans and irrigation design for amenity areas
  • Accessible route and play surface plans keyed to the ADA Standards
  • Specifications and details your contractor uses to bid and build

Planting plan coordinated with the community amenities site plan by Evergreen Design Group

Frequently Asked Questions

Community amenities design services cover the program, site layout, grading coordination, hardscape, planting, irrigation, and construction documents for shared outdoor spaces such as pools, playgrounds, pavilions, trails, and dog parks. Evergreen Design Group coordinates each package with your civil engineer and architect and issues documents for permitting and bid.

Bring the landscape architect in during schematic site planning. Amenity areas need level pads, drainage, and utility service, so locating them after grading is set adds retaining walls, fill, and utility rework. Early involvement lets the amenity program shape the grading and service layout instead of working around them.

Evergreen Design Group designs the pool deck, surrounding site, and equipment area, and produces the construction documents for them. We coordinate the pool shell, mechanical systems, and building connections with your pool engineer and architect, and deck drainage with your civil engineer. State and county health department rules set barrier, gate, and clearance requirements.

Amenities follow the 2010 ADA Standards for Accessible Design, including accessible routes, play areas, and pool access. Playgrounds also follow the CPSC Public Playground Safety Handbook, ASTM F1487 for equipment, and ASTM F1292 for surfacing. Local building and health department codes add requirements for pools, splash pads, and shade structures.

Pool decks, courts, plazas, and paved trails count as impervious area in most stormwater calculations. Evergreen Design Group provides amenity hardscape quantities so your civil engineer updates detention and water quality design. Permeable pavers and planted areas reduce runoff where local rules give credit for them.

Yes. Evergreen Design Group landscape architects are registered in 43 states, so one firm holds registration for amenity packages across a multi-state program. Our team works remotely across the country and coordinates with the civil engineers and architects in each market.

Send the amenity program or target list, the site plan or CAD base with topography, the project jurisdiction, and your schedule and budget targets. With those items, we confirm scope and deliverables and list the coordination points with your civil engineer and architect.

Amenity centers usually open with an early phase to support home sales. We size the first phase for the full program, reserve space and utility stubs for later additions, and phase the documents to match your builder and permitting schedule.

Contact Evergreen Design Group...

…to discuss your project’s community amenities design scope and timeline. We respond quickly and work efficiently — because we know your schedule matters.

Get in Touch with Us

Interested in creating an outdoor communities area that will be envied by your competitors? Fill out the form below, and our team will get back to you soon.